Toyota Avanza

40th TOYOTA INDONESIA ANNIVERSARY

2012-01-29T07:28:00.001-07:00

SPECIAL AFTER SALES PROGRAM- INDONESIA TOYOTA 40th ANNIVERSARY

In order toyota anniversary in Indonesia PT TOYOTA ASTRA MOTOR hold a car service program with prizes.
Program objectives are to as "umbrella program" commemorating 40 years of Toyota in INDONESIA with appreciation to pelanaggan faithful who continue to support Toyota's business in Indonesia.

Overview General Programs.
The name of the program SPECIAL PROGRAM AFTER SALES INDONESIATOYOTA-40 th ANNIVERSARY.
Where all models are manufactured TOYOTA mengituti this program should startfrom the Avanza, Innova, Camry, Corolla Altis, and the others except the limo.
Rules of the game where all the vehicles that do all kinds of services performed by the customer at the official workshop Toyota general repair and body repair.
System program is a lottery where customers fill out raffle tickets and then inserted into the coupon box program sweepstakes that will be raffled each month begins the program period from January to March 2012
Benefit for the customer is any customer a chance to win 1 unit VELOS ALL NEW Avanza 1.5 M / T, 3 units of ALL NEW Avanza 1.3 M / T, 40 units of SamsungGalaxy Tab 16 GB, 40 units of the Apple iPod Touch 4GB, and 400 units ofBlackBerry Gemini .
So hopefully guide the implementation of the program created the program "SPECIAL AFTER-SALES PROGRAM INDONESIA TOYOTA 40th ANNIVERSARY''Service you can enjoy car wins prizes.

All New Avanza & The All New Avanza Veloz

Avanza

2012-01-09T21:50:00.001-07:00

Toyota avanza 2012

Sales since its launch on 11th November every new advance later this month exceeded21,000 units, with a market share of 57%. Director of TAM, Hilman said Saladin All NewAvanza sales target in 2011 exceeded the target of a market share of 55% on the MPV.Payments until the end of 2010 140.000 units, while the end of September 2011 was 126 000 units, Hilman visit to New Avanza Sumatra, Java, Bali to Malang said yesterday.Luqman Hakim, said Sales Supervisor Sutoyo Auto2000 Malang, the development of all new Avanza sales reached 160 units, which expects to sell 230 units by the end of the year Auto2000 Sutoyo, breadfruit and Kartika Sari. Luqman confessed the pivotal point of all new Avanza a little more, he was optimistic that the new Avanza can all be perceivedby the market.
(Source: Bisnis Indonesia)
All New Avanza & The All New Avanza Veloz

ALPHARD TOYOTA

2012-01-09T21:36:00.000-07:00

toyota alphard 2012

TOYOTA ALPHARD

In the first year of the Dragon Air, Toyota-Astra Motor introduced the new Toyota Corolla with a glass on the outside and inside, to keep all of their superiority. Sampoerna Strategic Square, Sudirman, South Jakarta, Monday (09/01/2012) is entered President Director Johnny Darmawan TAM directly.

The completion of the exterior visible from the front, which looks more luxurious and powerful. Degrees of pressure is tough and strong. If the original bar grille consists of three, is now added four. Even with chrome on the hood, the decorated reinforce the impression of great strength. Fog bigger and stronger and can not be reduced to the previous version. The next section, changes in the design of the new light alloy wheels 17 inches in diameter. On the back there are improvements in the permit for the installation of the back is wider and reinforce the impression of stability. The new design rear lights also. In addition, other features remain such as the user as an artistic lighting, sunroof, metallic design company, until the chairs are practical.This does not change much in, because it is a luxury minivan is almost perfect. Show Alphard is a spacious bedroom, large sliding doors, a stool in the second row (may be with footrests, adjustable arms. All electrical control) equipped the torch is lit at the door for easy passenger night by the light of the lamp in the ceiling, reinforced the impression of luxury. This is not to stop Toyota continues to improve comfort and driving pleasure.Based on feedback from users for improvements in TAM-audio system. Number of speakers is now the tenth of the last eight. "But more than the increase in the number of speakers, New Alphard uses high-quality speakers with a focal length of Beryllium inverted dome tweeter for crystal clear audio is provided to all clients as well as produce," said Marketing Director of TAM, Joko Trisanyoto. Corolla two-tone dashboard by adding a dark, dark to enhance the impression of luxury enhanced.Alphard, that all functions, such as safetynya seven airbags (two front, left and right front passenger / driver, two on the glass and the other driver's knee), GOA body structure (body is designed so that the impact energy of the carrier), AFS (light come together to help the driver, there will be further look into the corner), the VCS, which helps the driver control the car in the corner at high speed.Continue to offer the best possible experience for you, the customer is Toyota, all of the new Alphard was acquired in January 2012 is assured tahun/50.000km tahun/50.000km third April. This is the last four years, new users need not worry Alphard thinking in health care "kencananya train." New Toyota Alphard comes with three options to meet the needs of 2.4 X, 2.4 and 3.5 V

BLOWER MOTOR FAN

2012-01-05T03:46:00.000-07:00

How to replace blower motor
Without you realizing that you sucking air every day your car is containing dust, why do so because without you realizing the dust dikarpet or footwear that you wear contain / carry dust from the outside.Cleaning the carpet every day it is nice to reduce the amount of dust dikarpet, but the dust that has been sucked and stuck in the blower motor fan if you are already clean.To find out how to clean the blower fan motor follow these instructions:
1.OFF THE CABLE FROM NEGATIVE BATTERY TERMINAL.
# Wait at least 90 seconds after removing the cable to prevent the airbags work.

2.OFF DOOR ASSEMBLY GLOVE COMPARTMENT.
# 2 Remove the hinge (the hinge).

# Release 2 stopper and drop the glove compartment door.

3.UNDER NO COVER OFF. 2 INSTRUMENT PANEL.
# Remove the Claw 3 Claw by hitting them in the direction of the arrow as shown in the figure, and take cover under instrument panel.
Note:Be careful when removing the Claw because it is easy to break, pull slowly.

4.BLOWER MOTOR FAN OFF.
# Remove the connector.
# Remove the 3 nuts and blower motor.

5.CHECK THE BLOWER MOTOR FAN.

# Clean the blower fan motor with a brush that has been given water that has been mixed with water.

# Dry the blower fan motor before replacing it.
Note:Be careful when cleaning not to wet the blower motor components
6.POST MOTOR BLOWER FAN.
# Replace the blower motor with 3 nuts.
# Attach the connector.
7.UNDER COVER POST NO. 2 INSTRUMENT PANEL.
#Link 3 clip and attach the lower instrument panel cover.
8.POST DOOR ASSEMBLY GLOVE COMPARTMENT.
# Enter 2 from the glove compartment door stopper.
# Link 2 hinge (the hinge).
9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL.
10.DO SOME INITIALIZATION.
# Perform the initialization using the following procedure:
Instructions:Do the following without stepping on the gas pedal:
* Turn the ignition to the ON position (do not start the engine) and wait for 5 seconds.
* Turn the ignition to the OFF position, and wait for about 15 seconds.
* Turn the ignition to the ON position and turn on the machine.
All New Avanza & The All New Avanza Veloz

FRONT WHEEL ALIGNMENT

2012-01-03T04:57:00.002-07:00

Sometimes the wheel alignment monitoring is part of standard automobile maintenance that consists of adjusting the angle of the wheel in terms of organized automobile manufacturers. The purpose of this adjustment is to reduce tire wear and to ensure that the vehicle is moving and real (not "pull" on the side).In your wheel alignment is the key, adjust the angle of the wheels so they are perpendicular to the ground and parallel to each other. The purpose of the adjustment is a maximum life of the vehicle tire and right and true when driving along straight and level.Some ways you can do to make your system more stable steering wheel while driving
1.CHECK TIRE BEFORE FRONT WHEEL ALIGNMENT
Check the tire pressure for installation and suitability.
Cold tire pressure:
Use a dial indicator, check the tire runout.
Tire runout:1.4 mm (0.055-in.) Or more
2.MEASURE VEHICLE HEIGHT BEFORE FRONT WHEEL ALIGNMENT

Heavy vehicles:
Tire Size AB CD
165/80R13 45.1 + / - 15 mm 42.5 + / - 15 mm
(1.78 + / - 12:59 in.) (1.67 + / - 12:59 in.)
185/70R14 45.1 + / - 15 mm 42.3 + / - 15 mm
185/65R15 (1.67 + / - 12:59 in.) (1.78 + / - 12:59 in.)
Point of measurement:
A:Ground clearance of front wheel center
B:Ground clearance of the bolt down the middle of the front suspension arm set
C:Ground clearance of rear wheel center
D:Ground clearance of the bolt side of the middle set of lower control arm front
CAUTION:* Prior to the wheel alignment, check the height of the vehicle.* Measure the height of vehicles when the vehicle is empty (with a full gas tank, spare tire and equipment keys.
INSTRUCTIONS:The vehicle to swing up and down at the corners to stabilize the suspension before check vehicle height.
3.TOE-IN EXAMINATION BEFORE FRONT WHEEL ALIGNMENT

Toe-in:
A+ B C-D
0 ° + / - 0 ° 12 '0 + / - 2.0 mm
(0 ° + / - 0.2 °) (0 + / - 0.08 in.)
INSTRUCTIONS:Just measure the C-D when A + B can not be measured.
If the toe-in is not included in the specification, set in both rack and.
4.SETTING TOE-IN BEFORE FRONT WHEEL ALIGNMENT
# Remove the clips steering rack boot.
# Loosen lock nut tie rod end.

# Turn to the right and left rack end with the same amount to adjust the toe-in.
INSTRUCTIONS:Try doing toe-in adjustments to the middle of the specification.
# Verify that the rack end left and right alike.
# Tighten the tie rod end lock nut to specification moment.

Occasion:47 N * m {480 kgf * cm, 35 ft lbf .*}
CAUTION:Adjust the angle tie rod end lock nut after tightening the tie rod end.
5.INSPECTION WHEEL ANGLE BEFORE FRONT WHEEL ALIGNMENT
Turn the steering wheel fully to the left and right, and measure the angle of rotation.
Wheel turn angle:Mechanical Steering Wheels Within Wheels of Foreign section
                                                                              (Reference)
Manual steering 45 ° 49 '+ / - 2 ° (39.20 ° + / - 2 °)
  (45.82 ° + / - 2 °) (39.20 ° + / - 2 °)

Power steering
43 ° 42 '+ / - 2 °) 37 ° 40' + / - 2 °
  (43.70 ° + / - 2 °) (37.67 ° + / - 2 °)
When the inner wheel angle right and left are not in accordance with the specifications, check the length of the right and left rack end.

6.CHECK camber, caster and SLOPE OF STEERING AXIS BEFORE FRONT WHEEL ALIGNMENT

# Put the front wheel in the middle of the alignment tester.
# Remove the wheel cap.# Set camber, caster, steering axis inclination gauge at the center of the axle hub.# Check the camber, caster and steering axis inclination.
Camber, caster and steering axis inclination.:
Camber Caster Steering Axis Tilt.
-0 ° 30 '+ / - 45' 4 ° 34 '+ / - 1 ° 12 ° 25' + / - 1 °
(-0.5 ° + / - 0.75 °) (4:57 ° + / - 1 °) (12:42 ° + / - 1 °)
CAUTION:* Do check when the vehicle is empty (with a full gas tank, spare tire and equipment keys).* Tolerance of differences between right and left wheels is 30 '(0.5 °) or less.
INSTRUCTIONS:There is no camber, caster or steering axis inclination adjustment mechanism.
If the measured value does not match the specification range, check the suspension parts and replace if necessary.
# Remove the camber, caster, steering axis inclination gauge and attachments.
# Replace the wheel cap.
All New Avanza & The All New Avanza Veloz

TIRE AND WHEEL

2012-01-03T03:08:00.000-07:00

TIRE AND WHEEL SYSTEM
To keep your tires more durable or easy to wear there are several ways you can doas follows:
1.CHECK TIRE
Check the tire pressure for installation and suitability.
Cold tire pressure:

Tire Size Front kPa (kgf/cm2, psi) Rear kPa (kgf/cm2, psi)

165/80R13 83S 220 (2.2. 32) 240 (2,4.35)

185/70R14 88S 210 (2.1. 30) 240 (2,4.35)

185/65R15 88S 210 (2.1. 30) 240 (2,4.35)

Use a dial indicator, check the tire runout.

Tire runout:
1.4 mm (0.055-in.) Or more

2.TIRE ROTATION
INSTRUCTIONS:
Rotate the tire as shown in FIG.

3.CHECK THE WHEEL BALANCE
Check and do off-car balancing.
If necessary, perform off-car balancing.

No balance after adjustment:
9.5 g (0.021 lb) or more

4.CHECK THE FRONT HUB BEARING AXLE

5.CHECK THE AXLE SHAFT REAR BEARING
All New Avanza & The All New Avanza Veloz

SET VALVE

2011-12-30T08:43:00.000-07:00

How to adjust valves toyota avanzaWhat causes you want to set the valve toyota avanza, toyota engine avanzaku whether the sound rude? or lack of energy avanzaku toyota engine, toyota engine speed may be unstable avanzaku or so-called lame avanzaku toyota engines.If you have a complaint please follow these instructions how to adjust valves toyota avanzaku as follows:1.OFF THE CABLE FROM NEGATIVE BATTERY TERMINAL
# Loosen the hose clamp and the air filter off the bolt, then remove the air cleaner hose No. 1.

2.Hose OFF AIR FILTERS NO 1
# Disconnect the VSV connector.
# Remove the 2 hoses.
# Remove the air temperature sensor.
# Unplug the vacuum sensor.
# Remove the vacuum hose.
# Remove the 3 bolts, then remove the air filter sub-assembly.
3.OFF AIR FILTER ASSEMBLY
# Remove the four connectors.# Remove the four bolts, then the ignition coil assembly.

4.IGNITION COILS OFF ASSEMBLY
5.OFF VENTILATION HOSE
6.OFF VENTILATION HOSE NO 2
7.OFF THROTTLE BODY BRACKET NO 2
# Remove the 2 screws, then remove the throttle body bracket 2.
8.DETACH CABLE MACHINE
9.DETACH PIPE RADIATOR SUB-ASSEMBLY
Remove the 2 screws, then remove the radiator pipe sub-assembly.

10.OFF CYLINDER HEAD COVER SUB-ASSEMBLY
# Remove the 11 bolts and 2 nuts in the order indicated in the figure, then the cylinder head.
11.CHECK SLIT VALVE
CAUTION:Check the valve gap in cold conditions.
# Set the 1 cylinder to TDC / compression.

* Rotate the crankshaft clockwise, to align the timing mark of crankshaft pulley with the pointer on the timing chain cover.

# Check that the adjustment mark on the camshaft timing sprocket is facing up. If not, turn the crankshaft 1 round until the signs are facing upwards.
# Check the valve gap shown in the picture.
* Use a feeler gauge, measure the gap between the valve lifter and camshaft.
Slit valve (Cold):Intake 0.145 to 0.235 mm (0.0057 to 0.0093-in.)Exhaust 0.275 to 0.365 mm (0.0108 to 0.0144-in.)

INSTRUCTIONS:If the gap is not in accordance with specification, record the measurement results are outside specification.
# Rotate the crankshaft clockwise one full turn and set cylinder No.. 4 to TDC / compression.
# Check the valve gap shown in the picture.
* Use a feeler gauge, measure the gap between the valve lifter and camshaft.
Slit valve (Cold):Intake 0.145 to 0.235 mm (0.0057 to 0.0093-in.)Exhaust 0.275 to 0.365 mm (0.0108 to 0.0144-in.)

INSTRUCTIONS:If the gap is not in accordance with specification, record the measurement results are outside specification.

12.SET THE SLIT VALVE
CAUTION:To prevent the valve does not collide with the piston when removing the camshaft, rotate the crankshaft in the direction of engine rotation approximately 90 ° from TDC / compression cylinder No.. 1.

# Remove the 2 screws, then remove the chain vibration damper 2.

# Remove the two bolts and timing chain cover stars. 2.

# Rotate the crankshaft pulley clockwise and 2 screw loose.

# Rotate the crankshaft clockwise, to align the timing mark of crankshaft pulley with the pointer on the timing chain cover.
# Check that the adjustment mark on the camshaft timing sprocket is facing up. If not, turn the crankshaft 1 round until the signs are facing upwards. (No. Cylinders. 1 at the position of TDC / compression).
# Give the paint mark on the timing chain is a straight plate with marks on the camshaft timing mark on camshaft sprocket and timing gear.
# Using a hexagonal lobes on the camshaft, loosen the screws that secure the camshaft timing sprocket.
CAUTION:The bolts can only be relaxed. Do not remove the bolts and sprockets.

INSTRUCTIONS:Loosen the bolt forward. If the bolt relaxed after removing the chain, the chain will be disrupted by the sprocket.

# Use a 10 mm hexagon key, remove the screw hole plugs chain service cap.
# Insert the screwdriver into the hole closed service chain, then move the stopper plate on the tensioner downward and hold it so as not to lock.

INSTRUCTIONS:This operation unlock the plunger on the tensioner.
# If the stopper does not release the lock plate easily, turn to the right and left to use hexagonal lobe on the camshaft.

# Using a hexagonal lobes on the camshaft, rotate the camshaft slightly to the right so that the plunger on the tensioner driven by chains.
# Remove the screwdriver from the hole closed chain services. Align the holes in the stopper plate and tensioner, then enter the lock hexagon diameter 2.5 mm (0.098-in.).
CAUTION:
*Hold the camshaft using the hexagonal lobe on the camshaft.
# Hold the diameter of 2.5 mm hexagon key (0098-in.) With adhesive tape so as not to be attracted to the outside.

INSTRUCTIONS:This operation is to hold the plunger on the tensioner in place.

# Remove the bolts fringe, then release chamshaft timing sprocket.

#Remove the bolts and loose chamshaft timing sprocket assembly.

#Remove the camshaft bearing cap No.. 1 and no. 2 in the sequence shown in FIG.

#Hold the timing chain by hand, then remove the camshaft. After removing the camshaft, hold down the chain by inserting a metal rod to prevent dropped chains.
# Use a micrometer, measure the thickness of the valve lifter that has been released.Calculate thick slit valve lifters so the valves are in the specification.
A. Choosing valve lifter.
B. Bold valve lifter is released.

C. Measurement slit valve.
Value specification (Cold):
Intake A = B + (C - 0.18 mm (0.0071-in.)).
Exhaust A = B + (C -0.31 mm (0.3099 mm.)).
# Select the new lifters with a thickness as close as possible to the value has been calculated.
INSTRUCTIONS:Lifter is available in 29 sizes with the addition of 0.020 mm (0.0008-in.), From 5.12 mm (0.2016-in.) Up to 5.68 mm (0.2236-in.).
Gap intake valves (Cold):Intake 0.15 to 0.23 mm (0.0059 to 0.2311 mm.)
EXAMPLE:Posted lifters 5.250 mm (5.2502 mm.), And the size of the gap is 0.400 mm (0.4013 mm.).Replace lifters 5.250 mm (5.2502 mm.) With a new size No.. 48 lifters.
New Lifter Thickness:No. Thickness No. Lifter. Thickness No. Lifter. Heavy Lifter
12 5,120 (0.2016) 32 5,320 (0.2094) 52 5,520 (0.2173)
14 5,140 (0.2024) 34 5,340 (0.2102) 54 5,540 (0.2181)
16 5,160 (0.2031) 36 5,360 (0.2110) 56 5,560 (0.2189)
18 5,180 (0.2039) 38 5,380 (0.2118) 58 5,580 (0.2197)
20 5,200 (0.2047) 40 5,400 (0.2126) 60 5,600 (0.2205)
22 5,220 (0.2055) 42 5,420 (0.2134) 62 5,620 (0.2213)
24 5,240 (0.2063) 44 5,440 (0.2142) 64 5,640 (0.2220)
26 5,260 (0.2071) 46 5,460 (0.2150) 66 5,660 (0.2228)
28 5,280 (0.2079) 48 5,480 (0.2157) 68 5,680 (0.2236)
30 5,300 (0.2087) 50 5,500 (0.2165) - -
Exhaust valve gap (Cold):Exhaust 0.28 to 0.36 mm (0.0110 to 0.3607 mm.)
EXAMPLE:Posted lifters 5.340 mm (0.2102-in.), And the size of the gap is 0.440 mm (0.0173-in.).Replace lifters 5.340 mm (0.2102-in.) With a new size No.. 46 lifters.
New Lifter Thickness:
No. Thickness No. Lifter. Thickness No. Lifter. Heavy Lifter12 5,120 (00002016) 32 5,320 (0.2094) 52 5,520 (0.2173)
14 5,140 (0.2024) 34 5,340 (0.2102) 54 5,540 (0.2181)
16 5,160 (0.2031) 36 5,360 (0.2110) 56 5,560 (0.2189)
18 5,180 (0.2039) 38 5,380 (0.2118) 58 5,580 (0.2197)
20 5,200 (0.2047) 40 5,400 (0.2126) 60 5,600 (0.2205)
22 5,220 (0.2055) 42 5,420 (0.2134) 62 5,620 (0.2213)
24 5,240 (0.2063) 44 5,440 (0.2142) 64 5,640 (0.2220)
26 5,260 (0.2071) 46 5,460 (0.2150) 66 5,660 (0.2228)
28 5,280 (0.2079) 48 5,480 (0.2157) 68 5,680 (0.2236)
30 5,300 (0.2087) 50 5,500 (0.2165 - -
# Replace the valve lifter is selected.
# Give the engine oil on the cam, cylinder head journaling, and above the valve lifters.

# Arrange so that the cam lobe camshaft cylinder No.. No. 3 and the cylinder. 4 on the intake side (camshaft) valve lifter push, No. cylinder and cam lobes. And No. 2.4 on the exhaust side (No. camshaft. 2) encourage the valve lifters.
# Check the front sign and the number and check that the sequence of stages as shown in the picture. Tighten the bolts in several stages as shown in FIG.

Occasion:13 N * m {127 kgf * cm, 9 ft lbf .*}
# For a pair of camshaft timing sprocket with the bolt.
# For the 2 pairs of camshaft sprocket with the bolt.
# Attach the chain so that the adjustment marks on the camshaft sprocket timing marks and paint, are made prior to demolition chains, have been straight.
INSTRUCTIONS:First, attach the chain to one of the camshaft. Rotate the camshaft to the right and to left using the hexagonal lobes on the camshaft timing so that the signs and signs painted on the sprocket on the chain to be straight.
Hexagon key Prison
# diameter 2.5 mm (0.098-in.) Of the tensioner.
INSTRUCTIONS:Using a hexagonal lobes on the camshaft, rotate the camshaft slightly to the left, then release the key Hexagon 2.5 mm in diameter (0098-in.) With a loose chain on the side of the tensioner.
# Using a hexagonal lobes on the camshaft, tighten the bolts used to mount the sprocket to the camshaft timing specifications moment.
Occasion:47 N * m {479 kgf * cm, 35 ft lbf .*}
# Give the adhesive on 2 or 3 screw on the end of the stopper bolt cap screw holes servicing chain.
CAUTION:Clean the oil contained in the bolts and bolt holes.
# Rotate the crankshaft pulley clockwise and temporarily plug the camshaft timing gear or sprocket with 2 screws fastening the camshaft timing gear indicated by the arrows in the figure. Then tighten the bolts to the moment of specification with 3 bolts.
Occasion:8.0 N * m {82 kgf * cm, 71 in .* lbf}
# Give the adhesive to 2 or 3 screw on the end of the stopper bolt cap screw holes servicing chain.
CAUTION:Keep the bolts and bolt holes are free from foreign matter and oil.
# Use a 10 mm hexagon key pretentious, plug the hole plug screw cap service chain.
Occasion:17 N * m {168 kgf * cm, 12 ft lbf .*}
# Replace the timing chain cover stars. 2.
# Give the packing seal as shown.Gaskets Sil:Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

# 2 Install the timing chain cover with 2 bolts.
Occasion:8.5 N * m {87 kgf * cm, 75 in .* lbf}
CAUTION:
* Clean any oil from the surface of contact.
* Replace the timing chain cover stars. 2 in 3 minutes after the use of packing seals.
* Do not start the engine at least 2 hours after installation.
# Install vibration damper 2 chain with 2 bolts.

Occasion:8.5 N * m {87 kgf * cm, 75 in .* lbf}13.POST CYLINDER HEAD COVER SUB-ASSEMBLY
# Set the cylinder head cover gasket in groove head cover, and insert the gasket into the boss in the head cover.
CAUTION:Insert the gasket perfectly until contact with the ribs.# Give the packing seal as shown.Gaskets Sil:Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

INSTRUCTIONS:Seal packing must have a width of 5 mm and a height of 2 mm.
# For a pair of cylinder head cover with 11 bolts and 2 nuts.

# Tighten bolts and nuts in several stages as shown in FIG.
Occasion:12 N * m {122 kgf * cm, 9 ft lbf .*} to bolt9.0 N * m {92 kgf * cm, 80 in lbf .*} for the nut
14.POST PIPE RADIATOR SUB-ASSEMBLY
15.POST CABLE MACHINE
16.POST NO 2 throttle body bracket
17.POST ASSEMBLY ignition coils
18.POST NO 2 ventilation hose
19.POST ventilation hose
20.POST AIR FILTER ASSEMBLY

# Replace the air filter with 3 bolts
Occasion:7.5 N * m {76 kgf * cm, 66 in .* lbf}
# Connect the vacuum hose to the vacuum sensor.
# Connect the vacuum sensor.
# Replace the air temperature sensor.
# 2 Attach the hose to the VSV.
# Connect the VSV connector.
21.PUT HOSE AIR FILTERS NO 1
22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
23.CHECK ENGINE OIL LEAK
All New Avanza & The All New Avanza Veloz

Cara Mengukur dan Menyetel Celah Katup Sepeda Motor ~ Belajar Otomotif Luar Kampus

2011-12-30T06:25:00.000-07:00

Cara Mengukur dan Menyetel Celah Katup Sepeda Motor ~ Belajar Otomotif Luar Kampus

All New Avanza & The All New Avanza Veloz

POWER STEERING FLUID CHANGE

2011-12-27T08:33:00.001-07:00

The workings of the hydraulic power steering
Power steering system uses engine power to operate the vane pump that produces hydraulic pressure. When the steering wheel is deflected, the oil circuit to the control valve is activated. When the oil pressure supplied to the power piston in the cylinder power, the power needed to move the steering wheel is reduced. This type requires a power steering fluid power steering leak checks periodically.

Power Steering Fluid Change
CHECK THE DRIVE BELT
# Check the belt visually from damage, such as excessive wear and fiber peeling.

# If damage is found, replace the drive belt.
INSTRUCTIONS:
Rift belt on the side of the rib is still acceptable. replace the belt if there are some missing ribs
DISPOSING AIR POWER STEERING SYSTEMS
# Check the fluid level.
# Jack the front of the vehicle and prop with a prop.
# Turn the steering wheel.
# With the engine off, steered wheel slowly from lock to lock several times.
# Lower the vehicle.
# Turn on the machine.Run the engine at idle for a few minutes rounds.
# Turn the steering wheel.
# With the engine idling, steered wheels to the left or right on full lock position and hold that position for 2 to 3 seconds.
Then turn the wheel to full lock position and hold the opposite position for 2 to 3 seconds (step A).
* Repeat steps (A) several times.
# Turn off the machine.
# Check for the existence of a foam or emulsion.Especially, if the system should be bleding twice as foam or emulsion, check for fluid leaks in the system.
CHECK THE FLUID LEVEL
# Keep the flatness of the vehicle.

# In case the engine off, check the fluid level in the reservoir oil.If necessary add fluid.
Fluid:ATF "DEXRON" II
INSTRUCTIONS:Check the fluid level is in the HOT range level in the reservoir tank. If the fluid is cold, check the fluid level in range COLD.
# Turn on the machine and let it sit idle.
# Turn the steering wheel from lock to lock position several times to increase the fluid temperature.
Fluid temperature:75 to 80 ° C (167 to 176 ° F)
# Check for the existence of a foam or emulsion.When the foam or emulsion arise, pass gas again the power steering system.
# With the engine idle, measuring the level of fluid in the reservoir oil.

# Turn off the machine.Wait a few minutes and measuring the fluid level in oil reservoir again.
Increasing the maximum fluid level:5 mm (0.20 ins.)
# If the problem is found, remove the power steering system of the wind again.Check the fluid level.
CHECK THE STEERING FLUID PRESSURE
# Remove the pressure feed tube from the pump vane
# Dispose of wind power steering system.
# Turn on the machine and let it sit idle.
# Turn the steering wheel from lock to lock position several times to increase the fluid temperature.
Fluid temperature:75 to 80 ° C (167 to 176 ° F)
# With the engine idle, close the valve and check the readings on SST SST.
Fluid pressure:5400 to 5900 kPa (55 to 60 kgf/cm2, 783 to 856 psi)
CAUTION:
* Do not leave the valve closed more than 10 seconds.
* Do not let the fluid temperature becomes too high.
# With the engine idle, full open valve.
# Measure the fluid pressure when the engine turns at 1,000 rpm and 3,000 rpm.
Fluid pressure difference:490 kPa (5 kgf/cm2, 71 psi) or less
CAUTION:Do not deflect the steering wheel.
# With the engine idle and fully open valve, swung the steering wheel to full lock position.
Fluid pressure:5400 to 5900 kPa (55 to 60 kgf/cm2, 783 to 856 psi)
CAUTION:
* Do not let the steering wheel in full lock position more than 10 seconds.
* Do not let the fluid temperature becomes too high.
# Remove the SST.
# Connect the pressure feed tube to the pump vane
# Dispose of wind power steering system.
CHECK THE STEERING effort
# Position the middle of the steering wheel assembly.
# Remove the steering pad
# Turn on the machine and let it sit idle.
# Measure the steering effort in two directions.
Steering effort (Reference):6.0 N * m (60 kgf * cm, 53 in .* lbf) or less
INSTRUCTIONS:Check the tire type, pressure and surface contact before making a diagnosis.
# Replace the steering wheel set nut assembly.
Occasion:34 N * m {349 kgf * cm, 25 ft lbf .*}
# Replace the steering pad
All New Avanza & The All New Avanza Veloz

TOYOTA PRIUS PHV 2012

2011-12-24T18:15:00.001-07:00

Toyota Prius PHV 2012

Toyota Motor Corporation announced, began receiving orders for the Prius plug-in or , which are published in Japan 30 January 2012. The advantages of the Prius PHV, the battery on the output power can be recharged at home. In addition, the fuel is more efficient than the hybrid.According to Toyota, the Prius PHV fuel consumption 61.0 km / liter. While the electric mode and the battery is fully charged, for a distance of 26.4 km. Therefore, estimates of Toyota, for those who cover short distances, can count on the EV mode, or lithium-ion batteries and batteries.Price
Since the Prius PHV a combination of electric vehicles and hybrid vehicles , and uses lithium batteries with high capacity, the price is more expensive. The standard, issued Rp373 billion, ¥ 3.2 million. The most expensive for ¥ 4200000 or Rp490 billion sold. The price includes taxes but not including the cost of recycling.High the price has dropped as low as possible. Because with a very low price as possible, Toyota hopes to promote electric vehicles. It is hoped that the public interest in their use.More weight
Lithium batteries used in Prius is 4.4 kWh and greater battery capacity than the Prius.According to the Toyota car battery causes the weight was 50 kg. To remove the accumulation by the weight of the batteries, relieves the body. Later, tires with low rolling resistance.The fuel consumption of 61.9 km / liter calculated based on road conditions from a combination of electric vehicles and high voltage. If you rely solely on the consumption of high-voltage consumption of electricity, instead of 31.6 km / link seedangkan 8.74 km / kWhSupport drive PHV

New features added to this car is a support service called Hart PHV. This allows the vehicle owner and connect to the Internet. Owners can also view the status of the vehicle via a smartphone, especially the battery status and location of the charging station. PHV Prius owners are also free to the charging station (station G), which is installed at the dealership by Toyota and other places.
All New Avanza & The All New Avanza Veloz

ENGINE TUNE UP CHECKLIST

2011-12-23T11:22:00.000-07:00

Engine Tune Up is whatever name you please specify what car if you experience decreased energy, so you must set up or re-check the condition of your car engineSo how do I Engine Tune Up is good and properly follow the instructions below:
CHECK THE LIQUID COOLING MACHINE
CHECK ENGINE OIL
CHECK THE BATTERIES
CHECK THE FILTER ELEMENT AIR FILTER SUB-ASSEMBLY
# Remove the air cleaner filter element sub-assembly.
# Check visually that there is nothing dirty, clogged, or damaged in the filter element air filter.
INSTRUCTIONS:
# If there is dirt or clogged air filter element, clean the air compressor.
# If there is dirt or blockage of the filter element is still left behind after the air filter was cleaned with air compressor, replace the air filter element.
CHECK THE BUSICHECK THE TIMING Ignition
# Heat engine.
# Put terminal tester from timing light in the position shown in FIG.
CAUTION:
* Use a timing light to detect the first signal.

# Use the SST, connect terminals 12 (EFIT) and 4 (E) of DLC3.
CAUTION:
*Be careful not one connecting terminal. Because it can damage the engine.
* Turn off all electrical systems and A / C.
* Check the ignition timing with a cooling fan to death.

#Check that the ignition timing is within the specification.
Ignition Timing:
4 to 8 ° BTDC
CAUTION:
When checking the ignition timing, move the transmission into park or neutral position.
INSTRUCTIONS:
* Run the engine at 1,000 to 1,300 rpm for 5 minutes, and check that the engine speed back to the idling rotation.
# Remove the terminal 12 (EFIT) and 4 (E)) of DLC3.

# Check that the ignition timing is within the specification.
Ignition Timing:-5 To 15 ° BTDC
# Check that the ignition timing as soon as engine speed plus advanced.
# Remove the timing light.

ROUND CHECK ENGINE IDLE
# Heat engine.
# Connect the SST to terminals 9 (REV) of DLC3. Connect the tachometer, then measure the engine speed at idle.
Round idle:750 rpm
CAUTION:
* When checking the idle rotation, move the transmission into park or neutral position.
# Turn off all electrical systems and A / C.
# Check the engine idle rotation with the fan cooling off.
CHECK compression
# Heat engine, then turn off.
# Remove the air filter assembly.
# Remove the ignition coil.
# Remove the spark plug.
# Unplug the fuel injector pump.
# Check the compression.
--- Insert the compression gauge into the spark plug hole.
--- Go to full throttle.

--- Turn the engine, and measure the compression pressure.
Compression pressure:1470 kPa (15.0 kgf/cm2, 213 psi)
Minimum pressure:1079 kPa (11.0 kgf/cm2, 156 psi)
Difference between each cylinder:147 kPa (1.5 kgf/cm2, 21 psi)

CAUTION:
* Use a fully charged battery so that the engine speed can be increased to 330 rpm or more.
* Check the other cylinder in the same way.
* Measure the compression pressure in the shortest time possible.
If the cylinder compression is low, pour a little oil into the engine cylinder, and then measure again.
INSTRUCTIONS:
* If the compression pressure increased after the addition of engine oil, piston rings may be worn.
* If the pressure remains low, the possibility of valve jammed or not seated properly, or there may be leakage from the gaskets.
CHECK THE CO / HC
# Turn on the machine.
# Run the engine at 2,500 rpm for approximately 180 seconds.
# Insert the probe tester probe CO / HC meter testing into the exhaust pipe of at least 40 cm (1.3 ft) during idling.
# Check the immediate concentration of CO / HC while idling.
The concentration of CO during idling.:0 to 0.2%
HC concentration during idling.
Local regulations are used
If the concentration of CO / HC is not in accordance with the rules, do troubleshoot below.
# Check the heated oxygen sensor work.
for possible causes of malfunctions, and inspect and repair parts to be used if necessary.
Normal CO, HC High, rough Idle Problem, Cause:
#Mistake Ignition:
---- Timing does not match
---- Spark plugs bad, short or gap is not suitable
# Gap improper valve# Leakage from the intake and exhaust valves
# Leakage in cylinder
Low CO, HC high, rough Idle Problem (Readings fluctuate HC), Cause:
# Leakage vacuum:
--- PCV Hose
--- Intake manifold
--- Throttle Body
--- ISCV
--- Channel brake booster
# Mixed skinny lawyer leading to failure
High CO, HC high, rough Idle Problem (Black smoke from exhaust) Cause:
# Constraints air filters
# PCV valve clogged
# EFI system error:
--- Error pressure regulator
--- Damage to water temperature sensor
--- Errors water mass flow meter
--- Error ECM
--- Error injector
--- Error throttle position sensor
All New Avanza & The All New Avanza Veloz

EFI

2011-12-22T05:39:00.000-07:00

EFI relay Toyota Avanza
Sometimes you are puzzled to determine whether a component or spare parts arestill good or not.
This dipostingan you can check whether your relay EFI Toyota Avanza masik good or not, I check the EFI relay Toyota Avanza:

CHECK THE ECU RELAY E.F.I

Check resistance using the ohmmeter measures resistance between the terminals
Detention standards when connecting terminals 3-5 are:
10 kΩ or higher
With a given voltage batery keterinal 1 and 2 we got the result below 1 Ω
If barriers are not in accordance with the specification, replace the EFI relay.
All New Avanza & The All New Avanza Veloz

THROTTLE BODY TOYOTA AVANZA

2011-12-20T07:03:00.000-07:00

Throttle Body Toyota Avanza
Throttle valve cable to work together with the accelerator pedal which is located in the interior of the vehicle, in order to adjust the volume of air-fuel mixture is sucked into the cylinder.How do I remove the Throttle Body Toyota Avanza

OFF THE CABLE FROM NEGATIVE BATTERY TERMINAL TOYOTA AVANZA

CLOSING DOWN OFF MACHINE (with Heater)
# Remove the 6 bolts and clips, and then remove the bottom engine cover.Drain engine coolant (with / Hose Heater)

WARNING:
To prevent the danger of heat, do not open the radiator cap while the engine and radiator are still hot. Liquid and hot vapor can spray out under pressure. Thermal expansion can cause engine coolant to heat and steam gushed out of the radiator assembly.

# Loosen drain plug radiator valves channel.
# Remove the radiator cap sub-assembly.
# Loosen drain plug channels water, then drain the coolant.

OFF AIR FILTER ASSEMBLY TOYOTA AVANZA
# Remove the intake air temperature sensor connector.
# Disconnect the VSV connector.
# Remove the charcoal canister hose No. outlet. 2.
# Remove the hoses from VSV.
# Unplug the vacuum sensor.
# Remove the vacuum hose from the sensor.
# Separate the reserve tank hose from the air filter hose clamps.
# Remove the four bolts, then remove the air filter and air filter hose

DETACH CABLE ASSEMBLY CONTROL accelerator TOYOTA AVANZA
# Remove the hose by-pass water No. 1 and by-pass hose No water. 2. (Without / heater hose)
# Loosen the nut shown in the picture, then unplug the cable acceleration control.OFF ASSEMBLY throttle body
# Remove the throttle position sensor connector.
# Unplug the idle speed control actuator.
# Remove the ventilation hose No.. 2.
# Remove the 2 bolts and bracket No. throttle body. 2.
# Remove the bolts, then separate the engine wire harness bracket from the throttle body.
# Remove the 2 bolts and the throttle body.
# Remove the O-ring from the intake manifold.

After Throttle Body Toyota Avanza has been freed from his home now you are doing demolition Throttle Body how to follow these guidelines:

OFF THE AIR FILTER bracket TOYOTA AVANZA
# Remove the 2 bolts and the air filter bracket.
SENSOR OFF throttle position
# Remove the 2 nuts and throttle position sensor.
OFF IDLE SPEED CONTROL ACTUATOR ASSEMBLY TOYOTA AVANZA
# Remove the two screws, then remove the actuator idle speed control.
# Remove the O-ring from the idle speed control actuator.

After Throttle Body Toyota Avanza has been dismantled now we do the examination on the Throttle Body how to check it out follow these instructions:
CHECK THE ASSEMBLY Throttle Body TOYOTA AVANZA

# Check that the throttle valve shaft does not creak.
# Check if there is no flow is blocked.
# Check that the throttle valve to open and close smoothly.
# Check if there is no gap between the throttle stop screw and throttle lever when the throttle valve is fully closed.
CAUTION:
Do not adjust the throttle stop screw.

CHECK THE IDLE SPEED CONTROL ACTUATOR ASSEMBLY TOYOTA AVANZA
#Check the detainees Use ohmmeter, measure resistance between the terminals.

When we connect the standard prisoner terminal 3-1 is:
45.6 to 50.4 Ω at 27 ° C (27.22 ° C)
When we connect the standard prisoner terminal 4-2 is:
45.6 to 50.4 Ω at 27 ° C (27.22 ° C)

If prisoners are not in accordance with the specification, replace the idling speed control actuator.

CHECK THE SENSOR throttle position TOYOTA AVANZA
#Check the detainees Use ohmmeter, measure resistance between the terminals.

Prisoners standard when you measure the terminal 1 (VC) - 2 (E2) results:
2.5 to 5.0 kΩ at 25 ° C (25.00 ° C)

If prisoners are not in accordance with the specification, replace the throttle position sensor.

Check the change in resistance when the throttle lever is fully closed.
Standard Prisoners increase proportionally to the throttle lever angle.Detention Standards (hint) if we connect the terminal 3 (VTA) - 2 (E2) results:
0.3 to 5.8 kΩ (fully closed)
Detention Standards (hint) if we connect the terminal 3 (VTA) - 2 (E2) results:
1.98 to 9.16 kΩ (fully open)

If prisoners are not in accordance with the specification, replace the throttle position sensor.

If all the components or sensors on the Throttle Body Toyota Avanza have been checked now again like you did the installation instructions:

POST ACTUATOR IDLE SPEED CONTROL ASSEMBLY TOYOTA AVANZA

# Install new O-ring on the idle speed control actuator.
# Replace the actuator idle speed control with 2 screws.
Occasion:
1.8 N * m {18 kgf * cm, 15 in. .* lbf}

POST POSITION SENSOR Throttle TOYOTA AVANZA
# Replace the throttle position sensor with 2 screws.
Occasion:
1.8 N * m {18 kgf * cm, 15 in. .* lbf}
POST BRACKET AIR FILTER TOYOTA AVANAZA
# Replace the air filter bracket with 2 screws.
Occasion :
7.5 N * m {76 kgf * cm, 66 in .* lbf}

POST ASSEMBLY throttle body bracket TOYOTA AVANZA
# Install new O-ring on the intake manifold.
# Give a thin layer of engine oil to the O-ring or throttle body.
# Replace the throttle body with 2 screws.
Occasion:
21 N * m {214 kgf * cm, 16 ft lbf .*}
# Install the engine wire harness bracket on the throttle body with a bolt.
Occasion:
7.5 N * m {76 kgf * cm, 66 in .* lbf}

# Replace the throttle body bracket No. 2 with 2 screws.
Occasion:
7.5 N * m {76 kgf * cm, 66 in .* lbf}
# Connect the vent hose No. 2 to the throttle body.
# Connect the idle speed control actuator.
# Connect the throttle position sensor connector
# Connect the water hose by-pass No.. 1 and by-pass hose No water. 2. (Without / heater hose)

POST ACCELERATION CONTROL CABLE ASSEMBLY TOYOTA AVANZA
POST AIR FILTER ASSEMBLY TOYOTA AVANZA
# Replace the air filter and air filter hose with 4 bolts.
Occasion:
7.5 N * m {76 kgf * cm, 66 in .* lbf}

# Install the reserve tank hose on air filter hose clamps.
# Connect the hose to the VSV.
# Connect the charcoal canister hose outlet No. 2.
# Connect the vacuum hose to the vacuum sensor.
# Connect the vacuum sensor.
# Connect the VSV connector.
# Connect the intake air temperature sensor connector.

CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
ADDED FLUID COOLING MACHINE (with / Hose Heater)
INSTRUCTIONS:
Engine coolant that does not fit can damage the engine cooling system.Use only Toyota Super Long Life Coolant or similar superior quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (tech engine coolant chemistry for long-life organic hybrid containing a blend of low phosphates and organic chemistry).

Toyota's new vehicles have been filled with Toyota Super Long Life Coolant. At the time of replacing the engine coolant, recommended Toyota Super Long Life Coolant.

CAUTION:
Do not use alcohol-based antifreeze or just water the soil only.

# Tighten all blockages.
# Loosen and remove the air-bleeding valve A and B.
# Fill the radiator with engine coolant from the filling hole.

CAUTION:
It is advisable to use deionized water or distilled water when diluting the engine coolant.

# Do not use excess water.
# Fasten A current of air bleeding valve engine coolant from the overflow valve A.
# Tighten the air bleeding valve B when the engine coolant from the overflow valve B.

CAUTION:
* Close the generator is placed under the air bleeder plug with cotton waste cloth or piece of cloth so that the generator is not wet by the engine coolant.* If the engine coolant from the overflow valve is not A or B, during step (e) through (f), tighten the valve after the engine coolant from the radiator overflow.

# Replace the radiator cap when the engine coolant from the radiator overflow.
INSTRUCTIONS:
Observe the engine coolant level in the radiator hose by pressing enter and exit radiator hose a few times by hand. When the engine coolant level goes down, add engine coolant.

# Fill the reservoir tank to the surface of the radiator is full.
# Turn on the machine and keep it in rotation 2000 rpm. Heat the engine until the cooling fan works.
INSTRUCTIONS:
When heating the engine, press the inlet and outlet radiator hose a few times.

# Turn off the engine and wait until the engine coolant temperature to cool. Then open the radiator cap and check the engine coolant level.
# If the surface of the liquid refrigerant to be down, repeat steps (b) to (i).
# When the surface of the coolant stops down, set the amount of coolant in the radiator reservoir tank.
Capacity:
A / T:
6.95 liters (7.3 U.S. qts, 6.1 Imp. Qts)
M / T:
6.8 liters (7.2 U.S. qts, 6.0 Imp. Qts)

CHECK THE RELEASE OF LIQUID COOLING (with / Hose Heater)

# Remove the radiator cap.
CAUTION:
To prevent the danger of heat, do not open the radiator cap while the engine and radiator are still hot. Liquid and hot vapor can spray out under pressure. Thermal expansion can cause engine coolant to heat and steam gushed out of the radiator.

# Fill the radiator with engine coolant and radiator cap tester pairs.
# Heat engine.
# Pump up to 137 kPa (1.4 kgf/cm2, 17.1 psi), then check that the pressure does not go down. If the pressure goes down, check for hose leaks, the radiator and water pump. If there is no sign of external leakage of engine coolant, check the heater core, cylinder block and cylinder head.
# Replace the radiator cap.

POST CLOSING DOWN MACHINE (with / Heater)
# Replace the engine cover with 6 bolts and clips.
Occasion:
6.0 N * m {51 kgf * cm, 53 in .* lbf}
All New Avanza & The All New Avanza Veloz

FUEL EFFICIENCY TOYOTA AVANZA

2011-12-19T06:58:00.000-07:00

IN AIR TEMPERATURE SENSOR

How to save fuel your vehicle from the start how much how to drive it right up to the addition of fuel saving devices, in addition you can also find out whether Toyota Avanza is in trouble with the fuel consumption.
There are several factors that affect fuel Toyota Avanza you are wasteful or not one of them used SIGN AIR TEMPERATURE SENSOR functional know how much fuelyour Toyota Avanza is needed when the intake air temperature which is inhaled by the engine.
Here you can find out whether AIR TEMPERATURE SENSOR SIGN found on Toyota Avanza is broken or not.

HOW TO CHECKING IN AIR TEMPERATURE SENSOR

Disconnect the cable from the battery negative terminal.
Disconnect the connector.
Remove the intake air temperature sensor.

Check the intake air temperature sensor.

Use an ohmmeter, measure resistance between the terminals between terminal 1-2by connecting the tester where the condition / or a good outcome measure is 2.21to 2.69 kΩ at 20 ° C (68 ° F) and 0.29 to 0.354 kΩ at 80 ° C (80.00 ° C).

If prisoners are not in accordance with the specification, replace IN THE AIR TEMPERATURE SENSOR

How to reassemble
Replace the inlet air temperature sensor.
Attach the connector.
Connect the cable from the battery negative terminal.

Turn your engine Toyota Avanza and see if the engine warning lights illuminate, ifthis happens do the reset by pulling the EFI fuse for 30 seconds, if you can notcontact admin @ teddy.sugandhi@ yahoo.co.id
All New Avanza & The All New Avanza Veloz

ENGINE COOLING TEMPERATURE SENSOR

2011-12-17T09:26:00.003-07:00

ENGINE COOLING FLUID TEMPERATURE SENSOR Toyota Avanza

Have you ever experienced water temperature indicator toyota avanza not move or die in the down position so that you do not know whether the condition of your engine toyota avanza good or too hot.To find out if the engine coolant temperature sensor is still good or not you follow these instructions:
1.IGNITION COILS OFF ASSEMBLY
2.OFF ventilation hose
3.NO OFF ventilation hose. 2
4.NO OFF throttle body bracket. 2
5.DETACH CABLE MACHINE
6.DETACH PIPE RADIATOR NO. 1 SUB-ASSEMBLY
7.OFF CYLINDER HEAD COVER SUB-ASSEMBLY
8.TEMPERATURE SENSOR LIQUID COOLING OFF MACHINE
After the liquid coolant temperature sensor removable machine do the measurement using the ohmmeter which you measure the resistance between the terminals of the terminal 1-2 when the results are 2.29 to 2.60 kΩ at 20 ° C (68 ° F) and 0.302 to 0.327 kΩ at 80 ° C (80.00 ° C)

If the results are not in accordance with the specification, replace the engine coolant temperature sensor.
CAUTION:
If the coolant temperature sensor is immersed in water for inspection, make sure that water does not enter into the terminal. Upon examination, delete water from the engine coolant temperature sensor.If the condition is unknown whether the sensor is already behind you now when the tide back in the following ways:
#POST ENGINE COOLING FLUID TEMPERATURE SENSOR
Connect the temperature sensor with a new gasket.
Occasion:
20 N * m {200 kgf * cm, 14 ft lbf .*}

#POST CYLINDER HEAD COVER SUB-ASSEMBLY
Set the cylinder head cover gasket in groove head cover, and insert the gasket into the boss in the middle of head cover.
CAUTION:
Insert the gasket perfectly until contact with the ribs.

Give packing seal as shown.
Gaskets Sil:Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

INSTRUCTIONS:
Seal packing must have a width of 5 mm and a height of 2 mm.For a while pairs of cylinder head cover with 11 bolts and 2 nuts.Tighten bolts and nuts in several stages as shown in FIG.

Occasion:
12 N * m {122 kgf * cm, 9 ft lbf .*} to bolt
9.0 N * m {92 kgf * cm, 80 in lbf .*} for the nut
#RADIATOR PIPE POST NO. 1 SUB-ASSEMBLY
#POST CABLE MACHINE
#POST NO throttle body bracket. 2
#POST NO ventilation hose. 2
#CONNECT ventilation hose
#POST ASSEMBLY ignition coils
All New Avanza & The All New Avanza Veloz